Netgear Router Fails to Connect with 5GHz Band

With any Netgear router, the 5GHz bands have both pros and cons. Though the 5GHz WiFi band provides faster throughput but it band provide lesser range too. So you might be wondering that how to speed up the performance of the 5GHz band on any Netgear WiFi router, right? Well, wonder no more!

In this post, we can help if you see poor performance on your 5GHz wireless band. Weak or poor 5GHz wireless band and intermittent WiFi connection are one of the biggest reasons behind the error. So let us take the plunge with the troubleshooting steps to fix issues related to your 5GHz band. Keep reading!

Troubleshooting 5GHz Band

Each of the troubleshooting steps highlighted below attempts to fix technical issues with the 5 GHz band. On the off chance if one step resolves the issue for you, do not proceed with the other troubleshooting steps.

Adjust the Position of your Netgear Router

Adjusting the placement of your Netgear router may help improve the 5GHz band signal and strength. So, to get the most out of your 5GHz band, relocate your Netgear router at the center, higher, and non-congested location of your house.

Adjust the Antennas on your Netgear Router

Some of the routers have adjustable antennas. So try adjusting the antennas on your Netgear router to acquire the best performance of your 5GHz band.

If still, you are unable to make the most out of your 5GHz band, ensure that you have properly performed Netgear router setup process.

Alternative Method to get 5GHz band over Netgear Router

Step-1: Check if your router is DFS i.e. Dynamic Frequency Section certified. Not every dual-band router support DFS.

Step-2: If your Netgear router is DFS certified, try to login to your device's configuration settings via routerlogin.

Step-3: Thereafter, under the router settings section, locate and click on the Wireless option.

Step-4: Now search for the 5GHz network section under the Wireless Channel option.

Step-5: If your Netgear router is set to “Auto” or DFS channel, it is suggested to change its value to 36-48 or 149-165.

Step-6: At last, click on the Apply button to save the changes.

Netgear Router Configuration Settings

Step-1: Connect your Netgear router to your modem or access point.

Step-2: Now access Netgear router login page via www.routerlogin.net.

Step-3: Navigate to Settings > Wireless > Connect Network.

Step 4: Your Netgear router will automatically scan the currently active WiFi network.

Step 5: Click on the Save button once you’re done. If you are facing issues while connecting to it, navigate back to the Settings option.

Step 6: Once you are there, select the “Extended 5GHz” band option and disable 2.4GHz.

Step 7: Click on the Save button once you’re done.

Bonus Tip:

To make the most of your router and its 5 GHz band, we suggest you perform Netgear Firmware update process. A regularly performed firmware update process fixes many big issues with your Netgear router and also helps in improving the performance of the 5 GHz band. But we also suggest you do not perform the Netgear router firmware update process until and unless you are aware of it. To make things happen, you can contact our technical department.

The Final Words

We hope that this particular blog helps you fix poor or weak 5GHz wireless band? If still, the issue is the same, feel free to get in touch with our experts via comments. And if the issue is resolved, please let us know, which troubleshooting tip has worked for you from the same source i.e. the comments section.

Oops! I am having Issues During Netgear Extender Setup. What to Do?

Is it safe to say that you are confronting issues with Netgear extender setup and mywifiext login? On the off chance if your answer is in yes, don’t worry as we have come up here to help you out.

In the event that you want to make a general change to the password or settings of your WiFi extender but unable to do so, at that point we guarantee you that after getting to know the simple instructions mentioned in this post, you will surely be able to troubleshoot the issue yourself.

Let’s Proceed With Simple Troubleshooting Steps:

Above all else, you need to remember that a usual updation of Netgear firmware and login password is essential if you need to change the settings, frequency band, or password of your wireless range extender.

For Netgear extender login, you need to interface your PC or laptop properly with the WiFi repeater. Open an internet browser and into the URL field, type 192.168.1.250. From that point forward, you are required to sign in to the account by filling the default username and password into the given fields.

In the event that you are unable to log in to the account, you can type mywifiext.net into the address bar field rather than the default IP address of your Netgear gadget.

In case you can’t log in, it is recommended you to reset your Netgear extender. For this, you need to get a paper clip or pen and embed it into the reset hole of the extender. Continue holding it for a few moments and after that, discharge it. This procedure will reset your gadget back to the default settings.

Connect Your Netgear Extender

In the event that your extender is associated physically with the router using an Ethernet cable, at that point we need you to disconnect both the gadgets from one another.

Interface the PC to the range extender with the same source, launch a web browser and either type the URL or default IP address of your range extender referenced previously in the address field. Hit enter and fill in the login certifications (default) to reach the Netgear genie smart setup page.

Once logged in, you can change the settings along with the password for your Netgear gadget according to your choice.

Try not to keep the settings as default. Make a solid and difficult-to-identify passphrase for your gadget. Now, save the settings and restart your gadget.

Bonus Troubleshooting Tips

  • Place your range extender within reach of your main WiFi network. Here, you need to ensure that the router, modem, and extender are up to date with the latest firmware version.

  • The Ethernet or USB link ought to be in decent condition.

  • Remove all the interference-resulting objects like microwave ovens, cordless telephones, metal objects, and electronic machines.

  • Additionally, turn off the public WiFi if using.

  • Place your range extender, modem, and router at a clean and higher shelf.

  • The internet browser you are utilizing for Netgear extender setup and login process ought to be significant, up-to-date, and free from a load of malicious files.

  • Ensure that your Netgear range extender is running the latest firmware version.

  • Restore the default factory settings on your Netgear WiFi range extender once and try setting it up again.

Here’s hope that you will now be able to sign in and fix login issues with mywifiext and Netgear extender setup.

If you find this post a lot helpful for you, keep in mind to share your valuable comments below. Moreover, if you have any queries then don’t hesitate to ask our professionals. We will definitely respond to you in a timely manner.

Solution to the Most Common Issues Related to Netgear Extender Setup

Netgear extenders are leading the race when it comes to providing blazing WiFi speed in all areas of your home. There are various models under the line of Netgear extenders however, the process to configure each and every model is the same.

Although by accessing the Netgear extender manual, users can easily configure their WiFi device, our technicians still receive a plethora of queries regarding the Netgear extender setup. If you are also having some questions in mind for doing Netgear extender setup, then the solution listed below for the most common issues might help you.

Fix: Netgear Extender Setup Frequently Asked Questions

What is the default web address to perform Netgear extender setup?

www.mywifiext.net is the default web address you can use to set up your WiFi device. If you own a MAC or iOS device, then try to configure the device using mywifiext.local.

Why my web browser is showing error message while accessing the Netgear extender login page?

Only an updated web browser will allow you to reach the login page of your range extender. So, if your web browser is not updated with the latest software version, then either download a new web browser on your system or update the one that is already installed on your Windows or MAC system.

What is the default IP address to be used for the Netgear extender setup?

192.168.1.250 is the default IP address to do the Netgear extender setup. 

How can I update the firmware of my range extender?

To update the firmware version of your range extender, you need to first log in to your extender via mywifiext. When you are on the dashboard of your device, navigate to settings and check if any new firmware version is available for the extender model you own. If available, get the update by hitting the Update Firmware option. 

Why I am not able to access Netgear extender login page?

  • There can be various reasons stopping you from accessing the login page of your Netgear WiFi range extender. You can fix the issues by checking:
  • If all your devices are properly connected to their wall sockets and receiving sufficient power supply.
  • The Ethernet cable you might have used to connect your router and extender is not dusty or damaged.
  • Your range extender is in the range of your WiFi router.
  • Your range extender is not getting any interruptions from things like fish tanks, aluminum studs, metal appliances, microwave ovens, baby monitors, Bluetooth speakers, reflexive surfaces, etc.
  • Whether you are entering the default web address correctly in the web address bar of your browser.
  • Whether you are entering the right credentials. If you have ever changed the default username and password of your extender, then you need to access the login page by making use of the changed details.

How can I set up my Netgear extender?

There are various methods to configure a Netgear extender. You can either use the WPS method or Netgear Installation Assistant.

Using the WPS method, you would be able to set up your device with the press of a button. However, for the Netgear Installation Assistant method, you would need to access GUI.

How can I recover the Netgear extender password?

If you have forgotten the password to access the login page of your range extender, then you need to reset your extender to the default factory settings and then configure it again.

In a Nutshell

We hope that the question in your mind regarding the Netgear extender setup has been answered. If the solution to your query is not listed above, feel free to contact us via comments. Your query will be answered by our expert technicians as soon as possible. 

Surefire Tips to Improve Netgear Extender’s Wireless Range

Wireless routers, adapters and access points send and receive radio wave signals via antennas. A majority of access points and routers include external visible antennae, but some are housed internally. Despite the fact that Netgear extender setup provides a great boost in the existing wireless range, yet some materials can reduce or stop radio waves. One such example is antennae which causes interference. This results in a decrease in the radio signal clarity as well as effectiveness.

This post will take the lid off on some surefire tips to optimize your Netgear extender’s wireless range. Scroll down and read more.

1. Positioning

Make sure to place your Netgear WiFi range extender in a central location, instead of a corner. Typically, public WiFi locations have access point mounted on the wall or ceiling. Also, keep the wireless extender away from interference-creating devices.

2. Avoid Interference

This refers to other electronic appliances which use the radio waves in the same 2.4 GHz and 5 GHz range. Microwaves, Bluetooth devices, cordless phones, radios, treadmills, washing machines, electric heaters, refrigerators, and related devices interfere with the wireless connectivity nearby. Doing so will also save you from mywifiext.net setup issues while configuring your Netgear WiFi range extender.

3. Minimize Obstructions

There must be an ideal line of sight between the access point and your wireless device (phone, tablet or laptop). Factors like wall thickness, number of walls, ceiling fans, and cordless phone base will also affect the signal strength. A metal filing cabinet will also shield the radio waves.

4. Antennae Type

Antennae don’t emit signals equally in all directions. Just like a reflector focuses a light beam, in the same manner, an antenna signal can be focused or blocked. Given that people can’t see radio waves, you should hinge on testing to get an idea of where antennas work most brightly. The main focus of antenna is either directional or omni-directional.

Let us tell you that omni-directional antennas are used in most home products and radiate horizontally all around. However, they are weaker downward or upward. These antennas are typically a few inches long rod.

On the other hand, a directional antenna alias a high-gain antenna radiates powerfully in a particular direction. It is typically a dish or flat panel. These antennas can be used for point-to-point transmissions while two antennae are focused directly at each other.

When you are near your directional antennae, you will get a signal even if you are out of the direction of its strongest signals. Nevertheless, you must be in the direction where the beam is most powerful when you are at longer distances.

4. Check Signal Strength

It all depends on the location. In general, increasing the signal strength may work but in an urban area or city, it won’t. In the case of too strong, your neighbors will choose your WiFi network. Power puts a great affect how far an antenna emits. Half or quarter signal strength would work very fine for most home users.

For Netgear WiFi range extenders, you can check the signal strength by accessing its configuration page via 192.168.1.250 IP address.

Voila! Our list of the failsafe ways to improve your Netgear WiFi range extender’s wireless range ends here. If you have any other tip in your treasure, do share with us via the comments box below.

An Ultimate Guide to Set Up a Linksys Range Extender

Linksys Wireless Extender is a treat for those who want to enjoy the usage of the internet without any interruptions. But sometimes, the process to set up the device becomes a difficulty for many users. If you are one of those, who are facing a problem with the Linksys Extender Setup, then this post is for you. This article will give you a nudge on how to set up Linksys Wireless Range Extender with ease in no time.

How to set up Linksys Range Extender

  • First and foremost step you need to follow is to connect your extender with your personal computer with the help of Ethernet Cable. 

  • To do this, simply plug one end of the cable into any LAN port of your PC and the other one into the Linksys Extender. 

  • Now, it's time to plug in your extender into the power socket using a power adapter. 

Bonus Tip: Try placing the extender in the area where you have faced low signal strength earlier. 

  • Now you are suggested to launch your preferred web browser which is supposed to be connected to the WiFi range extender. 

  • Fill the address bar with the default IP address and hit Go. 

  • Besides, you can also navigate to the official web address of your Linksys Range Extender. 

  • After accessing the setup page, you will face a tab namely “Get Started”. Simply hit on it. 

  • Now it's time to make a choice between configurations. Choose between 2.4 GHz and 5GHz and move further by clicking the Next button. 

  • Following the above steps, you will be taken to the wireless network settings by your setup wizard. The settings may include the name of the network (SSID), Security type and the Network Key. 

  • Again time to make selection. Choose a name that best suits you and do assign a password to your WiFi extender. 

  • Coming to the last step! Now you will be landing on the page having a tab named “Create Extended Network”. For your Linksys Extender Setup, all you need to do is just hit on this tab and you are all done.

If you are having the latest model of Linksys Extender, which is re6700 served with 802.11ac technology, then steps to set up for that can be different. Here's how to set up Linksys Extender re 6700. let's dive in and make things rolling! 

Linksys Extender re6700 Setup

Basic requirements for the setup are as follows:

  • AC power outlet

Let's now go through the various steps for Linksys Extender re6700 setup

  • Connect with the available wireless network called SSID 

  • Now, open your preferred web browser and enter the extender.linksys.com address bar 

  • Hit Enter > Start 

  • After this a screen will reveal in front of you where you will find that the checkbox is already checked related to Auto Update 

  • Moving to the next screen, you will come up with various wireless network options. Now, choose the one you are using. 

  • After the network selection, simply enter the password you set for your wireless secured network and hit Next.

  • Next option will ask you to change the name of your wireless network. After completing this, you are all done with the linksys re6700 setup process. 

After following the above points even if things are not going well then you can try Linksys Extender Reset. This will reset your device to its factory settings.

How To Fix Purple Screen Roku Error

Roku gives its users full access for streaming media over the WiFi. When connecting your Roku streaming device to the internet you may encounter error codes like the following.

  • 001.

  • 009.

  • 14.41.

  • 016.

  • 003.

  • 016.

  • 013.

  • 011.

  • 017.

  • 108.

  • 14.20.

  • 14.30.

  • 14.40

  • 14.50.

As a matter of fact, all the above-mentioned codes resemble that there might be a fault in your internet connection. And all above, there is a big and annoying issue - “Purple Screen Roku”.

Fix: Purple screen Roku – Unable to connect to the internet

While setting up Roku, you have to connect your Roku streaming device to your existing home WiFi network. After sometime, a list of available and active WiFi networks will be displayed. You just have to choose a network that belongs to you – type in the WiFi password carefully and proceed further.

Afterward, a strong WiFi connection will be established between your main wireless router or the access point (AP). In case, you are unable to connect your Roku device to the internet, then you will be unable to stream your favorite audios, videos, setup Roku account via roku.com/link and launch your preferred channels.

If you want to prevent this issue, then you have to make sure that you have active WiFi signals coming out of your main router or the access point. Given below are some

demystify steps that will be your guide to fix purple screen Roku – unable to connect to the internet issue.

  1. Go to “Roku settings” from your home screen, .

  2. Click on the “connection” button. You will find that if you are connected to the active WiFi connection or not.

  3. Enter the SSID (network name) of your wireless network (when prompt).

  4. Make sure that your main WiFi router is updated by the latest firmware technology. Moreover, also ensure that your router is placed openly on a higher shelf.

  5. If your signal strength is poor, then restart your router once.

  6. And, if the “purple screen Roku” issue still persists, then restart your Roku player as well.

  7. After a restart of your Roku streaming device, make sure that you have a valid and correct Roku activation code handy with you.

Apply the aforementioned tips and it will definitely fix the issues whatever you are facing.

Fix: Roku purple screen

As a matter of fact, the purple screen Roku indicates “High-bandwidth Digital Content Protection (HDCP) unauthorized – content disables error”. The chief reason behind this error is using a faulty or damaged HDMI cable. To get rid of this issue, we insist you to follow some easy to execute below-mentioned steps.

  1. In the first place, unplug the HDMI (High-Definition Multimedia Interface) cable.

  2. Turn off your Roku player and disconnect all the cables/wires that are connected with it.

  3. Wait for 2-3 minutes and after that, re-plug the HDMI cable. You have to set up your Roku player again using Roku link code.

  4. If possible, please use a high-quality HDMI cable.

  5. Use the same login credentials and the activation code for Roku you have used for setup Roku account earlier.

  6. Check the batteries of your Roku remote as well.

  7. Make sure that you are using correct Roku com link code while activating your device.

  8. HDMI cable should be properly instered. As a matter of fact, loose cable connections results in “purple screen Roku” or roku.com link code error.

  9. Make sure that your device is receiving up running internet connection from your main networking router.

If you experience the same issue even after following the demystify steps given in this post, then dial our Roku support number 1-855-795-5955 and ask our technical department for Roku support. We are the solution partner of Roku.

Read this to know the Roku Hacks: Register to Your Roku TV without Credit Car

Linksys RE6700 Setup Troubleshooting General Rules

The Linksys RE6700 AC1200 amplify dual-band WiFi range extender uses Wi-Fi protected setup to securely add compatible wireless devices automatically to your home network. But somehow, the WPS method fails and leads to some basic Linksys RE6700 setup errors. In this particular article section, we will try to find and troubleshoot the Linksys RE6700 extender setup issues.

Troubleshoot #1: You Fails to Get Connect with Your Connected Range Extender

  • Firstly check the position of your existing WiFi router and range extender. 

  • For the very first Linksys extender setup, you need to place your range extender close to your WiFi router. After that you have to set up your RE6700 range extender, you can unplug it and move it to the location where you found no network coverage area in your residence. 

  • To reduce the network signal obstructions, try to place your WiFi router and range extender into an alternate location. 

  • Try to reposition the Linksys RE6700 range extender's antennas. 

  • Keep both the router and range extender away from the metal objects, reflective surfaces, masonry walls, etc. 

  • Avoid to position the range extender near to other electronic devices that might create signal distortion. 

  • Meanwhile, if you are using WiFi Protected Setup (WPS) to connect, wait until the WPS LED indicator stops blinking before you try to make it connect again. If still the same try to go for Linksys extender reset .

    Troubleshoot #2: Your Wi-Fi Network Coverage Not Met With the Expectations

Try to reposition the antennas present on your Linksys RE6700 WiFi range extender. The antenna present on the left side of your range extender extends your network over a horizontal plane, so the ideal position is to parallel stand the antenna to the range extender. The right antenna extends your network on a vertical plane, so make it stand perpendicular to the range extender.

 

Troubleshoot #3: Fails to Access your Linksys Range Extender 

To access your Linksys RE6700 extender, you have to connect it with your home network. If you currently have wireless home network access, the problem maybe you have is that you have accidentally connected with a different wireless home network. So how to go for Linksys RE6700 setup and access it well.

 

To fix the Linksys RE6700 access problem on Windows Computers, do the following:

  1. On your Windows taskbar, you will find the wireless icon in the system tray, right-click on it. 

  1. Tap on the View Available Wireless Networks. A list of the available wireless network will appear up. 

  1. Now click on the own home network name. Click on Connect. 

  1. If you are prompted, now enter the network security key or password into the network key field. Now tap on Connect.

Now you will be able to access your Linksys RE6700 Wi-Fi range extender's settings interface. As you per your Windows OS version, there could be some variant in icons or wording.

 

To fix the Linksys RE6700 access problem on MAC Computers, do the following:

  1. In the menu bar present on the top of the screen, tap on the Wi-Fi icon. A list of wireless home networks will appear. Linksys smart Wi-Fi automatically assigned over your home network name. 

  1. Select your wireless home network of the router that you want to connect to. 

  1. Type the wireless network password/security key into the password field and then click on the OK button.

Now you should be able to access the Linksys range extender's configuration settings interface.

 

Troubleshoot #4: Fails to Access your Linksys Range Extender

Plugin your Linksys RE6700 range extender in the midway of your router and the area without Wi-Fi. Be sure you have at least 50% of your existing WiFi router's signals at the point on the device you prefer for setup.

We hope that our this particular article section on Linksys RE6700 Setup Troubleshooting General Rules completely stands on its perspective. Somehow if you still face some issue, feel free to share with us regarding Linksys extender through comments.


Read this  to setup Linksys WiFi Extender.